miscoat paint

1. The first thing we done was to make sure we were wearing the correct P.P.E (gloves, goggles and boots) we wore gloves to keep the paint off our hands so that we wood not acciodentaly spread paint every where. we wore steel toe capped boots to protect our feet from any heavy objects. we wore goggles to protect our eyes in case some of the paint got flicked.
2. the next thing we did was to get all the aquired tools (paint brush, bucket and water)
3. we then mixed some water with some paint for the miscoat.
4. then we began to spread the watered down paint all over the wall. 
5. once the paint had dryed we could see where we needed to fill
6. we then cleand up and reported that the job were done.

 

filling and sanding

1. The first thing we did was to put on the correct P.P.E (gloves, goggles and boots). we wore glove to protect our hands from anything sharp. we wore goggles to protect our eyes from any foreign objects. we wore steel toe capped boots to protect our feet from any heavy objects.
2. the next thing we did was to make up the filler we done this by getting dry fill and adding water and mixing untill it becomes a paste.
3. then we pushed the filler into any gaps in the plaster and waited for in to dry.
4. once the filler has dryed we then sanded down the excess by hand.
5. once it was all sanded down we then tidyed up  
6. finally we reported that the job were done  

architrave

1. The first thing we did was to make sure we had the correct P.P.E (gloves, goggles and boots).We wore gloves to protect our hands from splinters. We wore goggles to protect our eyes from any foreign objects. We wore steel toe capped boots to protect our feet from any heavy objects.
2. We then made sure that we had the correct equipment (hammer, nail, pencil and a mortis saw).
3. Then we marked out the lenght of the wood making sure we had anoth room for the 45 degress angle. We done this three time for each side.
4. We then assembled it al the wall around the door frame with a 10 mm gape around the door.
5. Then we nailed it to the wall so that it is sercure
6. Finally we tidyed up and repoted that the job were done.    

plaster board

1. The first thing we did was to make sure we wore our P.P.E (steel toe capped boots, goggles and gloves) we wore gloves to protect our hands from any splinter from the plaster board. We wore goggles to protect our eyes from any foreign objects. We wore steel toe capped boots to protect out feet from any heavy objects.
2. The next thing we did was to get any tools and material required (hammer, nail, plaster board, stanly knife, pencil and a straight edge). 
3. Then we measured out the area that we needed to cover with the plaster board
4. We then carryed the plaster board into the workshop and measured out where we need to cut.
5. After we cut the plaster board we put it up againt the wall to see if we needed to plane the edge. when it was ready we had to attach it to the wall.
6. Once the plaster board was fitted we then had to clean up. 
7.  Finally we reported that the job were done.
8. The next stage was to plaster.

plaster

1. The first thing we did was to put on our P.P.E (gloves, goggles and steel toe capped boots). we wore goggles to protect our eyes from any plaster that may have been flicked. We wore steel toe capped boots to protect our feet from any heavy objects. We wore gloves to protect our hands in case any one had a reaction to the plaster.
2.  The next thing we had to do was to get all of our tools and the materials required.
3. We then had to mix up the plaster. we did this by putting some water in a bucket and then we poured some of the water in to another bucket along with some plaster. we then mixed it up until it became the right density (not to runny and not to lumpy).
4. Then we made sure that all our tool we clean. then we putt a bit of plaster on our pallet an rubbed it in with the trell so that the plaster could not slide while we were plastering.
5. we then began to plaster our wall. we had to make sure that the first coat had lines so that we could polish them out after the first coat had set abit.
6. after we had polished out the lines on the wall we then had to begin another coat. after we placed all the plaster on the wall and polished all the line out. we made sure that the we filled all the area.
7. after the plaster had set we made sure that there are no lumps and if there were we could sand the down.
8. finally we cleaned the work area making sure there there is no plaster on the floor.
9. then we reported that the job were done.      

door frame

1. first we made sure we had the correct P.P.E (gloves, boots and goggles) we wore glove to protect our hands from splinters. we wore goggles to protect our eyes from any foreign objects. we wore steel toe capped boots to protect our feet incase we were to drop something heavy.
2. the next thing we did was to get all the materials and tools we needed.
3. we then marked out where to cut on the wood. after we marked out we then cut down the two line and chilsed out the wood.we done this twice
4. we then marked out a smaller bit of wood wich was going the be the top of our door frame.
5. then we assembled the frame on the ground making sure that the frame is square.
6. once the frame is assembled we then wedged it into place making sure that it is level.
7. finally we cut of the ends of the wedges and cleaned up the workshop. 
8. the next stage was to plaster the stud wall.