repairing door lock

The common defects to door locks

· The spring in they Mortice lock brakes

· Get stiff over time

· Poorly manufactured

Materials

· Mortice lock Chrome

· Madrid Lock Handle

The defects and limitations of door locks

· Different types of locks

· The type of levels on locks

· The poor or good make of they lock

Tools and PPE

· Pencil

· Cordless drill

· Machine Flat bits set

· Crosshead screw driver

· Bradel

· Chisel 25mm and 13mm

· Marking gauge

· Boots

· Gloves

· Goggles

Risk assessment

         there is a risk of splinters to hand

         there is a risk of dropping tools

     there is a risk of cuts form when chiseling

We wear correct PPE. To prevent these risks from happening. To stop splinters getting in hand wear gloves so it will not get right in when handling wood. Then to prevent cuts from chisel hold well and keep away form hands. And we boots so that if you drop a tool your feet will be safe. We are working to the health and safety act of 1974.

Method statement

We first got our PPE on, and then we made our way to the area of the door lock and saw that the lock was broken and the area around split and making the lock loose. So we tock all out and strted to mark up were it will be for the new slot for it to sit in. After its all mark and correct we started to dril holes in with a machine flat bit and then chsile to make look good and fit easly. Then after marked were the holes for they handle and key hole will be drill it out each side half way and fixed all together. So that it will cose but we have to move the door fram plat up a little so it will lock and hold in place as well. We got the plate and moved and marked it corisponding to the lock and chisled and driled a bit so it locks well. Then finished any last touches and packed away (plus clearance).

Quote

Dear customer

                        We have inspected door lock and the area around is all split and loose, so will replace with a new lock and hole.

 

      So we will mark up were it shall be, it will be half way in then center of the door and then cut the are of the lock will fit in to.

      After chiseled and made it to a nice fit and then make the area for a nice flush fit and chiseled it out a little.

      Then marked were handle and keyhole will be and then assembled all together and then check for any other problems and then start to finish up and pack away (plus clearance).

      Tthe time it will take around 3 hours to be completed

The Cost

Materials £50.00

Labour £60.00

fuel £10.00

 

Total cost £120.00

repair door frame

common defects

•  loose and moves
• splits in the wood
•  where the latch has broken off

materials

• soft wood door lining
• 2" screws

limations

• the wood bowing
• the wood twisting
• knots

tools and PPE

• pencil
• combination square
• tap measure
• saw
• cordless drill
• prozi drive screw head
• broom
• bin
• dust pan and brush
• steel toe capped boots
• glove
• goggles

risk assessment

there is a risk of splinter goin into your hand and causeing infection.
there is a risk of falling objects.
there is a risk of cutting your hand while sawing.

We wear correct PPE. To prevent these risks from happening. To stop cuts to hands wear gloves so any wood or splinters may not get in. Then to stop objects falling and hitting you must wear boots so that your feet will be protected. We are working to the health and safety act of 1974.

the method statment

the first thing we done was to make sure that we had the correct PPE. we then assess what we had to do. we then maked to 45 degee angels one above the damages part of the door frame and one below. we then cut both the 45 degree angles useing the panel saw. we then cut a new pice of wood so that it would fit flush with the door frame. once that was done we then attached it useing 2" screw. we then cleaned and tidyed away. 

quote

Dear customer,
                        after carefuly viewing your property we found the the door frame was splite we will need to cut the secton out and replace it.

       we will first mark the 45 degree angles of the door frame and then carfully cut them out makeing shure we do not do any damages to the wall. we will then cut to size and new bit of wood and we will make sure that it fits flush with the orignal door frame. we will then sercure it using 2" screw we will also dispose of the damaged bit of door frame.

The time it will take to complete will be around 2 hours

costs

materials £25.00
labour £60.00
fuel £10.00
disposing materials £10.00

Total cost £115.00

 

patch and repair plaster board

 common defects

• bows and loses shape if not stored correctly
• susceptible to water damage
• damage easy

material

• plaster board
• dry wall screws
• joining tape
• batten

defects

• there are differant types of plaster board 
• the are differant thinknessess of plaster board
• needs two people to carry it safly

tools and ppe

• knife
• tape measure
• level
• pencil
• cordless drill
• bin
• hop up
• dust pan and brush
• steel toe capped boots
• goggles
• dust mask
• gloves

risk assessment


There is a risk of breathing in the gypsum from the plaster board.
There is a risk of slipping while cutting the plaster board and inflickting injury to your self .
There is a tripping or slipping if the work area is not tidy.

We wear correct PPE. To prevent these risks from happening. To stop cuts to hand wear thick gloves and be careful when cutting as well. Then to stop the gypsum getting in lungs wear a dust mask or have a well ventilated room and last keep area clean for room to cut easily and to lower the risk of tripping or objects falling. We also worked to the Health and Safety Act 1974.

 

Method statment

 

the fist thing we did was to make sure we got the correct PPE on. we then looked over what needed doing. i then cutt the area that needed plaster boarding into a square. i the attached batten to the stud wall so that i could attach the plaster board. i then cut the plaster board to size and attached it two the wall with the dry wall screws makeing shure there is a 2 mm gap around the edges. i the screeded all around the edges. once that the plaster board was secure i the cleaned up and desposed of any non reusable materials.

 

quote

 

 

Dear customer

                      

                       after carfully viewing your property we will be able to apply plaster board to the damaged area. we will supply the plaster board that you require. we will the square of the damaged plaste board and attach batten to the stud wall. we will then cut the plaster board to size and attach it with dry wall screws.
         The time it will take to complete this will be around 2 hours     

the cost

materials £40.00
labour £60.00
fuel £10.00
disposeing of wast materials £20.00 

total cost £130.00

 

replaceing fence posts

The common defects to fence posts

      Rotting over time when in damp weathers

Ground movement moving posts out place

       Wind blowing it other or other natural stuff

Materials

            Fence Post 75mmx75x2.4m £30 (1)

            Postcrete 20kg £15 (2)

The defects and limitations of fence posts

            Bowing to wood

<          Twisted

            Wood rot

Tools

           Post Hole Digger

           Wheel barrow

           Tape

           Rubble bags

          String line

   
     Stop bored

           Crowbar

PPE

Boots

Gloves

Goggles

 

Risk assessment

           Getting Postcrete in eye

           Splinter

            Digging in the ground

We wear correct PPE. To prevent these risks from happening. To stop postcrete wear goggle all times when handling it and also wash off skin soon. Also wear gloves when putting in the hole and this will also cover form-getting splinters when handling post. Then wear boots to protect you form hitting with the post hole digger. We are working to they health and safety act of 1974.

We are working to they health and safety act of 1974.

Method statement

We first got our PPE on, and then we made our way to the area of were we shall be installing the posts to replace old posts you had on your fence. Then dug out the soil and made it 500mm deep so the posts will hold in place better. After it was all dug out and made hole wider with a crowbar and then we plumed the posts in hole and then pored in the postcrete per hole and add water and mix well will a good consistency and put soil back on top so it looks it was never there and then started to finish any last touches and packed away (plus clearance).

 

Quote

Dear customer

                        We have inspected fence posts and found the posts were losses and moved around too much so we shall replace the hole and make it stronger.

      So we first tock off fence panels and riles then removed post form hole and kept a safe area and tidy work place.

     Them we started to dig out existing postcrete and then started to make the same hole which was 500m deep.

      Then put the bag of postcrete in and tipped a bit of water will good mix and fill back up with soil and leave to set.

     After put all parts back together and then we checked everything was up to standard we then pack away (plus clearance).

Times

3 hours

Cost

The cost of all the materials and labour will be £200.00

Materials £60.00

Labour £30.00 per hour

fuel £20.00

disposing of materials £30.00

Total cost £200.00

fenceing

The common defects

• splits in the wood
• knots
• naterial bowing

  

Materials

• aris rails 8 ft 
• timber 800mmx25mmx100mm
• nails.

The defects and limitations

 

• bowing
• twisting
• wood rot

Tools

• nail gun
• compresser
• hammer
• cordless drill
• tap measure
• bin
• broom
• dustpan
• brush
• string
• screws
• level
• chisle

 

PPE

 

Boots

Gloves

Goggles

 

Risk assessment

 

 

We wear correct PPE to prevent these risks from happening.we wear the goggles to protect our eyes from bits of wood that chip up when using the chisle. we wore glove to protect our hands from splinstes and any prexisting nail in the wood. we wore steel toe capped boot to protect our feet from any falling objects and also due to people working around us with bricks. We also worked to the Health and Safety Act 1974.

 

Method statement

 

We first got our PPE on. we then made our way to the work area. once we were at the work area we then disposed of the existing panels and broken aris rail. The first thing we did was the make sure that the aris rails were cut to size. Then we chisled out the end of a new aris rail. we made sure that one side was smaller that the other so that it would slip into place easier. once that the aris rails were up we then attached the timber we left a 50 mm gap in between each of the pices of timber. we made sure that all the timber is level we done this while we were attaching the timber. once that all of the timber was attached we then tidyed up making sure that there were no problems. we then disposed of any non-reusable materials.  

 

 

 

Quote

 

Dear customer

                        After carfully viewing your property we have found that both of the aris rails have snapped and the panels are broken so we will need to replace both the aris rails and the panels

     we will first remove all of the broken materials. we will then shape and fit the new aris rails. Then we will fit the panels.

The labour will cost £30.00

The fence panels will cost £29.80

The aris rails will cost £10.00

Disposeing of materials will cost £60.00

Fuel £20.00



The total cot will be £149.80