attaching wast to sink

The common defects

one of the common defects is if one of the sealing rings are broken the the wast will proberly leak.

Materials

• bottle trap
• wast pipe
• elbow joint
• ring seal

limations

one of the limations is that if the seals are not tightend properly they can leak so befor testing we shall dobble check all seals.

Tools

• ajustable spanner
• hack saw
• boat level
• broom
• bin
• dust pan

risk assessment

there is a risk of slipping if any water spills so to reduce this risk will shall keep moping up any spills and we shall make sure that the public is aware of the risk by puttign up signs.

method statment

The first thing we have to do is to view the property and determent how much work is needed and the amount of time it will take. The next thing we will have to do is to get all the required materials and tools. We then will send a quote and if the client is happy we will then proceed with the work. we then first attach the trap to the bottom of the sink onc ethat is sercure we then we then attach an elbow joint to the trap. after that was sercure we the attached a 32mm wast pipe once that was surcured in to the right place we then attached another elbow joint sercured to the wast pipe. one that was all sercured we then attched another 32 mm waist pipe heading straight in to the bucket. once that was all done we tested it makine sure that there is no leaks. we then tidyed up and repoted that the job were done.    



quote

After carefully viewing your property i have come to a conclusion and hope that you will be happy with the quote any problem please do not hesitate to contact us.

bottle trap = £3.00
32mm wast pipe = £4.00
elbow joint = £8.00
labour = £60.00
fuel = £10.00



total = £85.00

replacing wash basin

The common defects

one of the common defects is over time the taps can seaze up and you will be unable to turn on and off you have to get the taps replaced to resolve that problem.

Materials

• taps
• wash basin
• flexible pipe
• tap connector

limitations

one of the limitations of the taps is that they need to be tightened before the sink is fitted to the wall other wise they become very difficult to tighten up because there is a lot of stuff in the way.
 

Tools

• ajustable spanner
• mole grips
• gloves
• steel toe capped boots

risk assessment

the is a risk of someone slipping so to reduce this risk we will keep mopping up any water and we shall make sure that people are aware that there is a hazard by putting up signs.

there is a risk of someone tripping over any materials left on the floor so to prevent this from happening we shall maintain our work area and make sure that any rubbish is disposed of.

method statement

The first thing we have to do is to view the property and determent how much work is needed and the amount of time it will take. The next thing we will have to do is to get all the required materials and tools. We then will send a quote and if the client is happy we will then proceed with the work.the first thing we done was to make sure the water is off.we will then fit the taps we do this by putting the sealing washer on first then we positioned the tap and put the backnut on to secure it in place. we tightened it up using a ajutable spanner. once the taps were secured we then attached the plug by making sure the rubber seal is n then putting the threaded part though the hole in the basin and then tightening it up with the backnut and a adjustable spanner. once the plug was attached we then fixed the basin to the wall and tided up.

 

quote

After carefully viewing your property i have come to a conclusion and hope that you will be happy with the quote that we have provided. any problem please do not hesitate to contact us.

labour £30 per hour = £ 50
wash basin including all fixings = £50.00
taps including all fixings = £17.00
fuel = £10.00



total = £127.00

repair toilet flusing cisten

The common defects

the common defect of the a velve is that it can become damage and make lould noise

a common defect of the ball vevel is that it could be set to high or to low.the resalt of this is that the toilet wont flush completey.

materials

• overflow
• velve
• ball flot
• water

limations

one of the limations of the bend flush is if it isent fitted propery water will end up spraying every where.

one of the limitation of the flush handle is that if tht isn't fitted properly to the lever arm the system wont flush of the handle will be at an angle.

tools

• mole grips
• ajustable spanner
• hack saw
• bin
• broom
• bucket
• p.p.e

risk assessment

there is a risk of slipping if any water was to get on the floor so to reduce this risk we shall keep moping up any water that spills and make sure that people are aware by putting up signs.

there is a of tripping over of cuts so to pervent this from happening we shall dispose of any non-reusable materials and store any resuable materials

method statment

The first thing we have to do is to view the property and determend how much work is needed and the amount of time it will take. The next thing we will have to do is to get all the required materials and tools. we then will send a quote and if the cilent is happy we will then proceed with the work.
the fist thing we done was to drain the existing water we done this holsing the flush down onc e the water was depleted we then took the sipfon we done this by taking the bolt of the bottom atached the the wast pipe. once we done this we then were able to take the siphon out to replace it. once we disposed of the old siphon we then attached a new one we done this by putting it in to position and attaching the waist pipe and then tighting it up. once that it was all done and every thing was tight we then tested it we done this by putting water into the citen and flushing it. once it was tested and all works we then tidyed up and repoted that the job were done.

quote

After carfully viewing your property i have came conclusion and hope that you will be happy with the quote any problem please do not hesitat to contact us.

siphon  £17
labour £30 an hour, per person = £30
fuel £10


total = £57.00

man hole cover

Common defects

Through weather conditons over the years, the drain can eventually start to get rusty and make it week, so people cna fall through it. The drain also starts to get bendy
 

Matrials

• Pug
• water
• drain cover

Limitations

Whislt laying the cement. It will make the drain very strong so it can take alot of weight. Inlcuding cars going over it, and people.
 

Tools

• spirit level (4ft)
• pointing trowel
• bucket
• bin
• broom
• dust pan

Risks assesment

There's a couple of hazards they you can fall down the man hole if the drain cover isn't strong enough. you can get the pug in your eye's. Some people can react with the pug and come out in a rash to the skin. Methord statment

The first thing we have to do is to view the property and determend how much work is needed and the amount of time it will take. The next thing we will have to do is to get all the required materials and tools. we then will send a quote and if the cilent is happy we will then proceed with the work.

We then had to get the correct p.p.e before we start. Gloves, Steel toe caps, goggles. We started to clean out the area and scooping the old pug out of the bricks and putting it in a bucket. We then took the drain off and started to put pug arund the edge. we kept making sure that the man-hole was level. once we made sure that it was all level we then smothered the puground so that we could get a good finish. once all the sides were smother we then tidyed every thing and made sure that no pug was in the drain because other wise it could cause a blockage. after ever think was tidy we then put the cover on and reported that the job were done.

 

 Quotes

3 x labours £9.00 per hours £54.00

fuel= £10.00
morta = £6
cover and frame = £20.00

Task will take 2hours

 

total cost = £90.00

clay pipe

 

Common Defects
 

clay pipes crack because they get to old, also when water runs through them for over a period of years it will start to decay.
materials:
The materials that we used for this job were two pipe connectors.
Defects in the materials:
The screws could become loose after a while and could also become rusty.

Tools:

· Saw Hacksaw
· Pencil
· screwdriver (flat-head)
· Mop and bucket
· dust pan
· broom
· bin

Risk assessment:

The risk assessment for this job is basically to wear your PPE and to be careful around a wet area, this is so that you don’t slip over. The PPE is so that you don’t get any sewage into cuts on your hands or so that when your cutting the pipe you slip and catch your foot, this is why you have to wear steel capped boots. Wear goggles just in case sewage water gets into your eyes.

Method statement:

Before you start the job make sure you get the tools you need ready, first mark out the part of the pipe you need to repair get a saw and cut the pipe where you have the cut marks when you have cut the pipe on one end of the pipe put a pipe connector and make sure it goes half way down when you have got it on the pipe tighten it up and put it on the pipe and tighten that end when you lay the pipe down against the other side mark off where the pipe end and the cut that part off. when you have done that slide the other pipe connector on the pipe then slide it across on to the other part of the pipe then tighten both sides up and make sure you have tightened them enough so it don’t leak

quote

After carfully viewing your property i have came conclusion and hope that you will be happy with the quote any problem please do not hesitat to contact us.

pipe connectors =£20

labour 3 men=£25

fuel =£15

Total:60

ridge tiles

common defects

the ridge tiles are brittle and brake easy. another common defect of the ridge tile is the weight they are quite heavy so you would not be able to keep carrying them up a ladder.

 material

• ridge tile
• clay tiles
• gaslvinised nails
• batten
• water
• pug
• 2 inch screws
• wall plugs

limitations

one of the limitationof the pug is that it cantains lime that can burn if left on you skin

tool list

• hammer drill
• masonary drill
• bucket
• joining iron
• pointing trowel
• hammer
• saw
• broom
• bin
• dust pan
• brush
• ear defenders
• gloves
• goggles
• steel boots

  risk assessment


there is a risk of tripping so to prevent this we will maintain a tidy work area

there is a risk of dropping the clay tiles on your fiit so to preven injury we shell wear steel toe capped boots.

methode statment


The first thing we have to do is to view the property and determend how much work is needed and the amount of time it will take. The next thing we will have to do is to get all the required materials and tools. we then will send a quote and if the cilent is happy we will then proceed with the work. we first removed the broken tile and replace them with the new ones so that we could get to doing the ridge tile. once we replace any broken tiles we will measure and mark out where the batten needs to go. we will then pre-drill a hole in then brick work with the hammer drill. once the holes are drilled we will then attach the batten to the wall so that the ridge tile can hold on. we will then pug the tile so that it is 10mm higher and 10mm away from the wall we will do this all the way alone. once that we attached them we will then make sure that all of the pug inbetween are smooth and have a good aperance with no hole for the water to get in. once we made sure that evey thing is up to standerd we will then tidy up and make sure that no tools are left on site.


quote

After carfully viewing your property i have came conclusion and hope that you will be happy with the quote any problem please do not hesitat to contact us.

ridge tiles = £10
tiles £5
galvinised nails £3
batten = £2.50
pug = £3
screew = £2.50
labour = £60
fuel = £10

total = £98.00